Home / Paint & Coatings / Suppliers / Clariant - Coatings & Construction Chemicals 科莱恩-涂料和建筑用化学品
Paint & Coatings
Clariant - Coatings & Construction Chemicals 科莱恩-涂料和建筑用化学品
Clariant - Coatings & Construction Chemicals 科莱恩-涂料和建筑用化学品 lists 334 grades in Paint & Coatings. The sheets saved on this site are below.
Grades from Clariant - Coatings & Construction Chemicals 科莱恩-涂料和建筑用化学品
Antimussol® 4752
Antimussol® 4752 is a defoaming agent for aqueous formulations. It is an aqueous solution of fatty derivatives with a small polysiloxane component. This white dispersion is used in a wide range of foaming media including: emulsion paints; polymer dispersions; emulsions and pigment dispersions; pigment preparations with organic and inorganic pigments, e.g. tinting pastes; concrete; works and waste water.
Antimussol® 4846N
Antimussol® 4846N is a defoaming agent for aqueous formulations. It is a mixture of hydrocarbons and fatty acid ethoxylates. Antimussol® 4846N is a combined defoamer/de-aerator with wetting properties. It develops its full efficacy in the acid and alkaline region. As a product which is free from phosphoric acid esters there is no danger to attack on plastics/rubbers. This product can be pre-diluted with water to a white emulsion. It can also be added in a water spray which is sprayed onto the foaming medium (e.g. to defoam wastewater). When mixing into concentrates Antimussol® 4846N should be added undiluted and stirred until homogeneous.
Antimussol® TIP
Antimussol® TIP is a general-purpose waste water defoamer. It is a mixture of phosphoric acid esters and isobutanol. The defoamer is supplied in ready-to-use form, and no further dilution is necessary. It can also be used as a defoamer for textile detergents. Antimussol® TIP destroys foam produced by the various classes of surfactant. The most effictive method of defoaming is to spray the product onto the foam.
Antimussol® TW Liquid
Antimussol® TW Liquid is a defoaming agent for aqueous formulations. It is a mineral oil-free defoamer based on fatty derivatives. This white, aqueous dispersion is sprayed onto the surface of the foaming medium preferably at points with high liquor turbulence, either undiluted or diluted up to 1:5 with water. It is suggested for the following applications: emulsion paints; polymer dispersions; emulsions and pigment dispersions; pigment preparations with organic and inorganic pigments, e.g. tinting pastes; preferably acid detergent formulations; concrete; works and waste water; and metal processing agents.
Antimussol® V 5084 Liquid
Antimussol® V 5084 Liquid is a defoaming agent for aqueous solutions. It is a mixture of ethoxylated and nitrogen containing components with silica. Antimussol® V 5084 liquid has a good resistance against salts, acids and alkalines. It has a good compatibility with anionic, nonionic and cationic auxiliaries. This product is suggested for the following applications: emulsion paints; polymer dispersions; emulsions and pigment dispersions; pigment preparations with organic and inorganic pigments, e.g. tinting pastes; surfactant formulations; and concrete.
Antimussol® V 5348 Liquid
Antimussol® V 5348 Liquid is a defoaming agent for aqueous solutions. It is a blend of liquid hydrocarbons with silica and fat derivatives. This product is a highly effective liquid defoamer with emulsifying abilities in water. Therefore this defoamer type is especially suitable for the use in low viscous and and unpigmented systems. Of course Antimussol® V 5348 liquid can also be used in highly filled systems especially when a fast distribution of the defoamer is desired. For manufacturing of emulsions it is necessary to add always the defoamer to the water. This product is typically used in the following applications: emulsion paints; polymer dispersions; emulsions and pigment dispersions; pigment preparations with organic and inorganic pigments, e.g. tinting pastes; surfactant formulations; and concrete.
Arkopal® N 040
Arkopal® N 040 is a nonionic surfactant for the chemical industry. It is a nonylphenolpolyglycolether with 4 Mol EO. This viscous, slightly yellow liquid is most suitable for mineral oils, petroleum and similar aliphatic hydrocarbons.
Arkopal® N 060
Arkopal® N 060 is a nonionic surfactant for the chemical industry. It is a nonylphenolpolyglycolether with 6 Mol EO. This viscous, slightly yellow liquid is most suitable for mineral oils, petroleum and similar aliphatic hydrocarbons.
Arkopal® N 080
Arkopal® N 080 is a nonionic surfactant for the chemical industry. It is a nonylphenolpolyglycolether with 8 Mol EO. This viscous, slightly yellow liquid is most suitable for aromatic hydrocarbons.
Arkopal® N 090
Arkopal® N 090 is a nonionic surfactant for the chemical industry. It is a nonylphenolpolyglycolether with 9 Mol EO. This viscous, slightly yellow liquid is most suitable for aromatic hydrocarbons.
Arkopal® N 100
Arkopal® N 100 is a nonionic surfactant for the chemical industry. It is a nonylphenolpolyglycolether with 10 Mol EO. This viscous, slightly yellow liquid is most suitable for aromatic hydrocarbons.
Arkopal® N 1000
Arkopal® N 1000 is a nonionic surfactant for the chemical industry. It is a nonylphenolpolyglycolether with 100 Mol EO. This white up to slightly yellow wax is used as an emulsifier and dispersing agent, and as an emuslifer for bitumen.
Arkopal® N 110
Arkopal® N 110 is a nonionic surfactant for the chemical industry. It is a nonylphenolpolyglycolether with 11 Mol EO. This viscous, slightly yellow liquid is most suitable for chlorinated hydrocarbons.
Arkopal® N 130
Arkopal® N 130 is a nonionic surfactant for the chemical industry. It is a nonylphenolpolyglycolether with 13 Mol EO. This slightly yellow, pourable paste is most suitable for aromatic hydrocarbons.
Arkopal® N 150
Arkopal® N 150 is a nonionic surfactant for the chemical industry. It is a nonylphenolpolyglycolether with 15 Mol EO. This slightly yellow paste is most suitable for chlorinated hydrocarbons.
Arkopal® N 230
Arkopal® N 230 is a nonionic surfactant for the chemical industry. It is composed of Nonylphenolpolyglycolether with 23 Mol EO. Being nonionic, the Arkopal N grades are compatible with all other nonionic, anionic or cationic substances. Electrolytes, for example neutral salts, alkalis and – to a lesser extent – acids, reduce the water solubility of the Arkopal N grades and may lead to their salting out, especially at high concentrations and temperatures. This slightly yellow wax is most suitable for fatty acids (olein) and waxes.
Arkopal® N 238
Arkopal® N 238 is a nonionic emulsifier for the chemical industry. It is composed of nonylphenol polyethylene glycol ether with 23 mole ethylene oxide. Arkopal® N 230 is used in the following applications:as emulsifier in emulsion polymerization; as wax emulsifier; for pigment pastes; as stabilizer in paints and coatings.
Arkopal® N 300
Arkopal® N 300 is a nonionic surfactant for the chemical industry. It is composed of nonylphenolpolyglycolether with 30 Mol EO. The Arkopal® N grades have excellent resistance to compounds that cause hard water, to metal salts, including those of heavy metals, acids, alkalis, reductive agents and oxidative agents based on peroxide. This slightly yellow wax is most suitable for fatty acids (olein) and waxes.
Arkopal® N 307
Arkopal® N 307 is a nonionic emulsifier for the chemical industry. It is composed of nonylphenol polyethylene glycol ether with 30 mole ethylene oxide. This product is used in the following applications: as emulsifier in emulsion polymerization; as wax emulsifier; for pigment pastes; and as stabilizer in paints and coatings.
Arkopal® N 308
Arkopal® N 308 is a nonionic emulsifier for the chemical industry. It is composed of nonylphenol polyethylene glycol ether with 30 moleethylene oxide. Arkopal® N 308 is used in the following applications:as emulsifier in emulsion polymerization; as wax emulsifier; for pigment pastes; as stabilizer in paints and coatings.
Arkopon® T Paste 8015
Arkopon® T Paste 8015 is an anionic emulsifier, wetting and dispersing agent for coating applications. This yellow paste is composed of sodium alkyl methyl tauride. Arkopon® T Paste 8015 is used in pigment preparations for inorganic pigments e.g. for titanium dioxide. It offers high pigment loads, low viscosity and high tinting strengths.
D-FOAM-R C113
D-FOAM-R C113 is a 100% active foam control additive formulated for use
D-FOAM-R C113E
D-FOAM-R C113E is a 100% active foam control additive formulated for
D-FOAM-R C114
D-FOAM-R C114 is a 100% active, organic defoamer formulated for use in
D-FOAM-R C114E
D-FOAM-R C114E is a 100% active, organic defoamer formulated for use
D-FOAM-R C117
D-FOAM-R C117 is a 100% active, organic defoamer formulated for use in
D-FOAM-R C330
D-FOAM-R C330 is a highly effective, non-silicone foam control additive for
D-FOAM-R C740
D-FOAM-R C740 is a highly effective silicone containing antifoam that
D-FOAM-R C920
D-FOAM-R C920 is a 100% active, silicone antifoam compound that is specially formulated for use in UV, EB and solvent borne inks and coatings. It offers excellent foam and entrained air control in many systems with good compatibility.
Diethylene Glycol Dibutyl Ether
Diethylene Glycol Dibutyl Ether is a clear, colorless liquid with a characteristic odor. The solvent features a low freezing point, high boiling point, and low viscosity. It is miscible in any ratio with solvents such as ethanol, acetone, benzene, ether, and chlorinated hydrocarbons. It has little to no solubility in water and high molecular weight aliphatic hydrocarbons. DEGDBE is an excellent solvent for a wide range of polar and non-polar substances.
Diethylene Glycol Dimethyl Ether
Diethylene Glycol Dimethyl Ether is a neutral, slightly volatile, colorless liquid. Because of the free electron pairs at the oxygen atoms it has high solvating power and is miscible with water and all common solvents in any ratio. As a result of its chemical stability and the absence of reactive groups, Diethylene glycol dimethyl ether can be used as an inert reaction medium for many organic and organometallic reactions and for polymerizations.
Dipropylene Glycol Dimethyl Ether
Dipropylene Glycol Dimethyl Ether (DPGDME) is a colorless liquid with a mild, pleasant odor. It is completely miscible with most common organic solvents. However, it has limited solubility in water. DPGDME has no hydroxyl functionality. It is an inert, aprotic solvent and can be used in proton sensitive systems. Dipropylene Glycol Dimethyl Ether is not listed as a Hazardous Air Pollutant, has low toxicity, and offers an alternative to solvents being phased out as a result of the Clean Air Act. Due to its chemical stability and the absence of reactive groups, DPGDME can also be used as an inert reaction medium, e. g. for reactions with alkali and alkaline-earth metals (Grignard reactions), polymerizations etc.
Dispersogen® 1728
Dispersogen® 1728 is an anionic dispersing agent for pigments and minerals. It is used for water based and solvent based pigment preparations, disperse dyes and printing inks. This product is suitable for inorganic pigments, carbon black and organic pigments. The advantages of Dispersogen® 1728 are: high pigment concentration, low viscosity of the preparation, high stability of the preparation and low foaming. This slightly cloudy, viscous or pasty liquid is composed of an aqueous solution of a novolac derivative.
Dispersogen® 2774
Dispersogen® 2774 is a nonionic dispersing agent for pigments and minerals. It is used as a dispersing agent for aqueous and solvent based pigment preparations and printing inks. Dispersogen® 2774 is specially suitable for carbon black and for organic pigments in aqueous pigment preparations. The advantages of Dispersogen® 2774 are: high pigment concentration, low viscosity of the preparation, high stability of the preparation in a wide temperature range and low foaming. This yellowish, viscous to pasty liquid is composed of a novolac alkoxylate.
Dispersogen® 2774-1
Dispersogen® 2774-1 is a nonionic dispersing agent for pigments. This yellowish, viscous to pasty liquid is composed of novolac alkoxylate in ethylene glycol. It is suitable for inorganic pigments (metal oxids), carbon black and specially for organic pigments (polycylcic and phthalocyanine pigments) that are difficult to disperse in aqueous pigment preparations. The advantages of Dispersogen® 2774-1 are high pigment concentration, low viscosity of the preparation, high stability of the preparation in a wide temperature range and low foaming.
Dispersogen® 2774-2
Dispersogen® 2774-2 is a nonionic dispersing agent for pigments and minerals. This yellowish, viscous liquid is composed of novolac alkoxylate in propylene glycol. Dispersogen® 2774-2 is used as a dispersing agent for aqueous pigment preparations, and it is soluble in organic solvents e.g. ethylene glycol and propylene glycol and compatible with many solvent based preparations. This product is suitable for inorganic pigments, carbon black and especially for organic pigments (polycylcic and phthalocyanine pigments) that are difficult to disperse in aqueous pigment preparations. The advantages of Dispersogen® 2774-2 are high pigment concentration, low viscosity of the preparation, high stability of the preparation in a wide temperature range and low foaming.
Dispersogen® 3169
Dispersogen® 3169 is a anionic dispersing agent for pigments. This brownish, clear liquid is an aqueous solution of an anionic novolac derivative. Dispersogen® 3169 is used for water based and solvent based pigment preparations, disperse dyes and printing inks. It is suitable for inorganic pigments, carbon black and in particular for organic pigments. The advantages of Dispersing® Agent 3169 are high pigment concentration, low viscosity of the preparation, high stability of the preparation and low foaming.
Dispersogen® 4387
Dispersogen® 4387 is an anionic dispersing agent for pigments and minerals. It is used for water based, solvent based of water / solvent based pigment preparations, paper printing inks, textile printing pastes and coatings. Dispersogen® 4387 is suitable for inorganic pigments (metal oxids), carbon black and especially for organic pigments (polycylcic and phthalocyanine pigments) that are difficult to disperse.
Dispersogen® ASN Powder
Dispersogen® ASN Powder is a dispersing agent for the chemical-technological industry. This white powder is composed of ethoxylated higher alcohol. It is a dispersing agent for pigments and pigment preparations. In addition, this product is also applied as an auxiliary for dyeing and printing of textiles.
Dispersogen® LFH
Dispersogen® LFH is an anionic dispersing agent for pigments and minerals. This brownish, viscous liquid is free of any additional biocide. Dispersogen® LFH is an anionic AP-free dispersing agent and used for water / solvent based pigment preparations. It is suitable for inorganic pigments, carbon black and for organic pigments. The advantages of Dispersogen® LFH are: high pigment concentration, low viscosity of the preparation, high stability of the preparation in a wide temperature range and low foaming.
Dispersogen® LFS
Dispersogen® LFS is an anionic dispersing agent for pigments and minerals. This brownish, viscous liquid is free of any additional biocide, and it is composed of Polyarylalkylphenol polyethylene glycol ether phophoric acid ester. Dispersogen® LFS is an anionic AP-free dispersing agent and used for water-based, solvent-based or water / solvent based pigment preparations. It is suitable for inorganic pigments, carbon black and for organic pigments. The advantages of Dispersogen® LFH are: high pigment concentration, low viscosity of the preparation, high stability of the preparation in a wide temperature range and low foaming.
Dispersogen® UDN
Dispersogen® UDN is a mixture of nonionic dispersing and wetting agents used in pigment preparations. This yellowish liquid is suitable for inorganic pigments, organic pigments, and carbon black to produce stable, free flowing pigment preparations with high solid contents. Dispersogen® UDN is used in emulsion paints to improve compatibility of pigments and minerals with polymers and binders and to enhance the tinting strength of organic pigments.
Dodigen® 4131
Dodigen® 4131 is a cationic surfactant for the chemical-technological industry. This colourless to slightly yellow liquid is composed of stearyl dimethyl benzyl ammonium chloride. It is used for manufacturing of organophilic bentonite, antistatic agent.
Dodigen® 4140
Dodigen® 4140 is a quaternary ammonium compound for water treatment. It is used for the clarification of oilfield producted waters, industrial waste and process waters. It is also a demulsifier for used emulsions. This clear, viscous liquid is composed of quaternary ammonium polymer.
Emulsogen® 3896
Emulsogen® 3896 is an emulsifier for emulsion polymerization. This pale yellowish wax is composed of oleic alcohol ethoxylate with 20 moles ethylene oxide. It is is used as an emulsifier in emulsion polymerization, particularly in the manufacture of polyvinylacetate homo- and copolymer dispersions. Emulsogen® 3896 is resistant to water hardness salts and to acids and alkalis in the concentrations normally used. This product can be used in combination with other nonionic and anionic surfactants.
Emulsogen® 4084
Emulsogen® 4084 is a nonionic emulsifier for emulsion polymerization. This pale yellow wax is composed of block copolymer of propylene oxide and ethylene oxide, containing 60% w/w ethylene oxide. Emulsogen® 4084 is used in emulsion polymerization of polyvinyl acetate, acrylate and styrene/acrylate dispersions to stabilize the rheological behaviour of the polymer dispersions and to improve the electrolyte and shear stability. It can be used in combination with other nonionic, anionic and cationic surfactants.
Emulsogen® APG 2019
Emulsogen® APG 2019 is a copolymerizable anionic emulsifier and hydrophilic monomer for emulsion polymerization. This yellow to brown liquid is composed of allyl phenylpolyol ether sulfate with 20 EO, ammonium salt. It is used as emulsifier and comonomer in emulsion polymerization, particularly in the manufacture of acrylate, styrene/acrylate and vinyl acetate/acrylate emulsions.
Emulsogen® APS 100
Emulsogen® APS 100 is a copolymerizable anionic emulsifier and hydrophilic monomer. It is used as emulsifier and comonomer in emulsion polymerization, particularly in the manufacture of acrylate, styrene/acrylate and vinyl acetate emulsions. The advantages of Emulsogen® APS 100 in comparison to conventional emulsifiers are the ability of copolymerisation to reduce migration, improved freeze- thaw, electrolyte and shear stability of the polymer emulsion and reduced water sensitivity and water up-take of the polymer film.
Emulsogen® APS 100 S
Emulsogen® APS 100 S is a copolymerizable anionic emulsifier and hydrophilic monomer for emulsion polymerization. It is composed of allyl polyalkylene glycol (10 EO) ether sulfate, sodium salt. Emulsogen® APS 100 S is used as an emulsifier and comonomer in emulsion polymerization, particularly in the manufacture of acrylate, styrene/acrylate and vinyl acetate/acrylate emulsions with low volatile (organic) components.
Emulsogen® DMR
Emulsogen® DMR is an emulsifier for emulsion thickeners based on mineral oils. This white, waxy flake substance is composed of fatty acid polyethylene glycol phosphoric acid ester. It is used as an emulsifier in mineral oil thickeners. The dosage is about 5 – 30 g/l Emulsogen® DMR. Such mineral oil emulsions are used e.g. in textile printing processes together with reactive dyestuffs.
Emulsogen® EPA 073
Emulsogen® EPA 073 is an anionic emulsifier, wetting and dispersing agent. This product is designed for use as an emulsifier in the production of acrylic and modified acrylic polymers and vinyl acetate copolymers used as pigment binders in coatings for paper and paperboard complying with 21 C.F.R. Sections 176.170 and 176.180 in contact with all types of food.
Emulsogen® EPA 1954
Emulsogen® EPA 1954 is an anionic surfactant for industrial applications. It is used as an emulsifier for emulsion polymerization to produce polymer dispersions. The use of Emulsogen® EPA 1954 allows the production of polymer dispersions with controlled particle size and low coagulation during the polymerization process.
Emulsogen® LA 083
Emulsogen® LA 083 is an anionic emulsifier and dispersing agent. It is composed of alkyl polyethylene glycol ether sulphate with 8 mole ethylene oxide, ammonium salt. This product is readily biodegradable and free of additional preservatives. Emulsogen® LA 083 is used as an emulsifier for emulsion polymerization of vinyl acetate, acrylic acid esters, methacrylic acid esters, styrene and other monomers. This product is also used as a dispersing agent for pigments to produce low viscous, stable pigment dispersions.
Emulsogen® LCA 073
Emulsogen® LCA 073 is an anionic emulsifier, wetting and dispersing agent. It is composed of alkyl polyethylene glycol ether sulphate with 7 mole ethylene oxide, sodium salt. Emulsogen® LCA 073 is used as an emulsifier for emulsion polymerization of monomers like styrene, acrylic acid esters, methacrylic acid esters and vinyl acetate. In addition, it is used as a wetting agent for inorganic and organic pigments in preparations. Emulsogen® LCA 073 also produces stable, low foaming emulsions of organic solvents, hydrocarbons, oils and waxes in water.
Emulsogen® LCN 050
Emulsogen® LCN 050 is a nonionic emulsifier for industrial applications. It is composed of alkyl polyethylene glycol ether with 5 mole ethylene oxide. This product contains no additional biocides. Emulsogen® LCN 050 is used as a wetting agent end emulsifier in emulsions, detergents, paints and coatings.
Emulsogen® LCN 070
Emulsogen® LCN 070 is a nonionic emulsifier for industrial applications. It is composed of alkyl polyethylene glycol ether with 7 mole ethylene oxide. This product is readily biodegradable and contains no additional biocides.
Emulsogen® LCN 088
Emulsogen® LCN 088 is a nonionic emulsifier for industrial applications. It is composed of alkyl polyethylene glycol ether with 8 mole ethylene oxide. This product is readily biodegradable and contains no additional biocides. Emulsogen® LCN 088 is used as a wetting agent for industrial applications in aqueous solutions of 1 - 5 g/l and as a dispersing agent in paints and coatings for fillers and pigments in concentrations of 0,1 - 1,0 %.
Emulsogen® LCN 118
Emulsogen® LCN 118 is a nonionic emulsifier for industrial applications. It is ready biodegradable and contains no additional biocides. This product is used as an emulsifier for emulsion polymerization to improve the shear, temperature and electrolyte stability of polymer dispersions. Emulsogen® LCN 118 is also used as a dispersing agent for emulsion paints to improve the scrub resistance.
Emulsogen® LCN 158
Emulsogen® LCN 158 is a nonionic emulsifier for industrial applications. It is composed of alkyl polyethylene glycol ether with 15 mole ethylene oxide. This product is is readily biodegradable and contains no additional biocides. Emulsogen® LCN 158 is used as an emulsifier for emulsion polymerization improving the shear, temperature and electrolyte stability of polymer dispersions. It is also used as a dispersing agent for emulsion paints to improve the scrub resistance.
Emulsogen® LCN 217
Emulsogen® LCN 217 is a nonionic emulsifier for industrial applications. It is composed of alkyl polyethylene glycol ether with 21 mole ethylene oxide. This product is ready biodegradable and contains no additional biocides. Emulsogen® LCN 217 is used as an emulsifier for emulsion polymerization improving the shear, temperature and electrolyte stability of polymer dispersions. This product is also is used as a dispersing agent for emulsion paints to improve the scrub resistance.
Emulsogen® LCN 287
Emulsogen® LCN 287 is a nonionic emulsifier for industrial applications. It is used as emulsifier for emulsion polymerization of vinyl acetate, styrene and acrylate homo- and copolymers together with anionic surfactants like Emulsogen® EPA 073. Emulsogen® LCN 287 improves the shear, temperature and electrolyte stability of polymer dispersions. It is used as a dispersing agent for inorganic and organic pigments in aqueous pigment preparations.
Emulsogen® LCN 407
Emulsogen® LCN 407 is a nonionic emulsifier for industrial applications. This clear liquid to white pasty product is ready biodegradable and containsno additional biocides. Emulsogen® LCN 407 is used as an emulsifier for emulsion polymerization improving the shear, temperature and electrolyte stability of polymer dispersions.
Emulsogen® LCN 506
Emulsogen® LCN 506 is a nonionic emulsifier for emulsion polymerization. It is composed of alkyl polyethylene glycol ether with 50 mole ethylene oxide. This product is readily biodegradable and contains no additional biocides. Emulsogen® LCN 506 is used as an emulsifier for emulsion polymerization improving the shear, temperature and electrolyte stability of polymer dispersions. It can be diluted with water at room temperature without forming a strong gel phase.
Emulsogen® LS
Emulsogen® LS is an anionic emulsifier for emulsion polymerization. It is composed of C12 - Alkyl sulphate, sodium salt in water. Emulsogen® LS is an anionic emulsifier for emulsion polymerization of e.g. E-PVC, polyvinyl acetate, acrylate and styrene / acrylate - dispersions.
Emulsogen® OLS
Emulsogen® OLS is an emulsifier and foaming agent composed of disodium oleyl/cetyl sulphosuccinamate. This yellowish, cloudy liquid is used as an emulsifier and foaming agent in carpet backing with styrene / butadiene latices.
Emulsogen® PF 20 S
Emulsogen® PF 20 S is an emulsifier for emulsion polymerization. This yellowish brown liquid is composed of polyalkylene glycol ether sulfate, ammonium salt. Emulsogen® PF 20 S is resistant to water hardness salts and to acids and alkalis in the concentrations normally used. It can be used in combination with other nonionic and anionic surfactants. Emulsogen® PF 20 S is used as an emulsifier in emulsion polymerization, particularly in the manufacture of acrylate and styrene / acrylate dispersions.
Emulsogen® RAL 100
Emulsogen® RAL 100 is a nonionic polymerizable emulsifier. This yellowish liquid/paste can be used as a polymerizable emulsifier and a hydrophilic, water soluble monomer in emulsion polymerization. It is soluble in water at 20 °C.
Emulsogen® RAL 109
Emulsogen® RAL 109 is a nonionic polymerizable emulsifier. This clear, yellowish liquid is composed of allyl polyalkylene glycol ether with 10 mole EO. It can be used as a polymerizable emulsifier and a hydrophilic, water soluble monomer in emulsion polymerization.
Emulsogen® RAL 208
Emulsogen® RAL 208 is a nonionic polymerizable emulsifier. This clear, yellowish liquid is composed of allyl polyalkylene glycol ether with 20 mole ethylene oxide. It can be used as a polymerizable emulsifier and a hydrophilic, water soluble monomer in emulsion polymerization.
Emulsogen® RAL 307
Emulsogen® RAL 307 is a nonionic polymerizable emulsifier. This clear, yellowish liquid is composed of allyl polyalkylene glycol ether with 30 mole EO. Emulsogen® RAL 307 can be used as a polymerizable emulsifier or a hydrophilic, water soluble monomer in emulsion polymerization.
Emulsogen® SB 10
Emulsogen® SB 10 is an anionic wetting agent and emulsifier composed of sodium diisodecyl sulfosuccinate in a solvent mixture. It is used in emulsion polymerization of vinyl acetate, acrylate and acrylate / styrene dispersions, E-PVC and SBLatex. This product is also used as a wetting agent in aqueous paints and coatings.
Emulsogen® SF 8
Emulsogen® SF 8 is an anionic emulsifier and wetting agent. This cloudy liquid is composed of sodium di(2-ethylhexyl) sulfosuccinate in water. It can be used as a wetting agent for emulsion polymers, e.g. SBLatex for carpet coating. Emulsogen® SF 8 can also be used as a cake dewatering aide and as a wetting agent for aqueous, VOC-free paints and coatings.
Emulsogen® TAS
Emulsogen® TAS is an emulsifier and foaming agent. This yellowish, liquid emulsion is composed of disodium tallow alkyl sulphosuccinamate. Emulsogen® TAS is used as an emulsifier and foaming agent in carpet backing with styrene / butadiene latices. It is soluble in water.
Emulsogen® TO
Emulsogen® TO is an emulsifier for the chemical-technological industry. This yellow oily liquid is composed of fatty acid ester. It is applied as an emulsifier for mineral oil, O/W and W/O emulsions.
Emulsogen® TS 100
Emulsogen® TS 100 is a nonionic wetting and dispersing agent for organic pigments in dispersions, preparations and coatings. It is composed of Tristyrylphenol-Polyglycolether with approximately 10 moles ethylene oxide. This product is free of any additional biocide. Emulsogen® TS 100 has a HLB value of about 10 and is used for aqueous pigment dispersions, preparations, paints and coatings.
Emulsogen® TS 160
Emulsogen® TS 160 is a nonionic wetting and dispersing agent. It has a HLB value of about 13 and is used for aqueous pigment dispersions, preparations, paints and coatings. Emulsogen® TS 160 is suitable for organic pigments and carbon black to produce stable, free flowing pigment preparations with high solid contents and with low viscosities.
Emulsogen® TS 200
Emulsogen® TS 200 is a nonionic dispersing agent and emulsifier. It is is suitable for organic pigments and carbon black to produce stable, free flowing pigment preparations with high solid contents. Emulsogen® TS 200 improves the compatibility of pigments and minerals with polymers and binders. It also improves shelf life and stability of emulsion paints.
Emulsogen® TS 290
Emulsogen® TS 290 is a nonionic dispersing and wetting agent for organic pigments in dispersions, preparations and coatings. It is composed of Tristyrylphenol-Polyglycolether with approximately 29 moles ethylene oxide and is free of any additional biocide. Emulsogen® TS 290 has a HLB value of about 15 and is used for aqueous pigment dispersions, preparations, paints and coatings.
Emulsogen® TS 298
Emulsogen® TS 298 is a nonionic dispersing and wetting agent for organic pigments in dispersions, preparations and coatings. It is composed of Tristyrylphenol-Polyglycolether with approximately 29 moles ethylene oxide. This yellowish liquid is free of any additional biocide. Emulsogen® TS 298 has a HLB value of about 15 and is used for aqueous pigment dispersions, preparations, paints and coatings.
Emulsogen® TS 407
Emulsogen® TS 407 is a nonionic wetting and dispersing agent for organic pigments in dispersions, preparations and coatings. This yellowish liquid is composed of tristyrylphenol-polyglycolether with approximately 40 moles ethylene oxide. It is free of any additional biocide and is used for aqueous pigment preparations, paints and coatings.
Emulsogen® TS 540
Emulsogen® TS 540 is a nonionic wetting and dispersing agent for organic pigments in dispersions, preparations and coatings. This yellowish wax is composed of tristyrylphenol-polyglycolether with approximately 54 moles ethylene glycol. It is free of any additional biocide and is used for aqueous pigment preparations, paints and coatings. Emulsogen® TS 540 is suitable for organic pigments and carbon black to produce stable, free flowing pigment preparations with high solid contents. This product improves the compatibility of pigments and minerals with polymers and binders. It prevents skinning of emulsion polymers in paints and improves the shelf life and stability of emulsion paints.
Emulsogen® TS 600
Emulsogen® TS 600 is a nonionic dispersing and wetting agent for organic pigments in dispersions, preparations and coatings. This yellowish wax is free of any additional biocide, and it is suitable for organic pigments and carbon black to produce stable, free flowing pigment preparations with high solid contents. Emulsogen® TS 600 improves the compatibility of pigments and minerals with polymers and binders. It prevents skinning of emulsion polymers in paints and improves the shelf life and stability of emulsion paints.
Fluowet® ETC 100
Fluowet® ETC 100 is an easy-to-clean coating for ceramics and glass. It is composed of a solution of partially condensated silanes in alcohol. The silanes polymerize and form a polymer coating on silicate surfaces. Water pearls of the coated surface and stains like lime soap can not adhere strongly to the surface. Fluowet® ETC 100 is suitable for ceramic tiles in kitchens, glass doors of shower cabins and ceramic sanitary ware, wash basins and bath tubes.
Fluowet® ETC 300
Fluowet® ETC 300 is a concentrated coating material which is diluted with water and applied on ceramic tiles and sanitary ware to produce hydrophobic and oleophobic coatings with easy-to-clean effects. Water pearls of the coated surface and stains like lime soap can not adhere strongly to the surface. Easy-to-clean coatings produced from Fluowet® ETC 300 show an aesthetic appearance due to the shape of the water pearls with high contact angles. This product is suitable for ceramic tiles, ceramic sanitary ware, wash basins and bath tubes. The aqueous dilutions from Fluowet® ETC 300 are used for spray coating.
Fluowet® FS 600
Fluowet® FS 600 is a perfluoroalkyl triethyoxysilane raw material for the preparation of easy-to-clean coatings. This clear colourless to pale yellow liquid is used for the synthesis of nanocomposites together with other silanes and partially hydrolysis of the silanes to produce reactive condensates. The perfluoroalkyl chain of Fluowet® FS 600 contributes to the hydrophobic and oleophobic effect of the coating.
Fluowet® FS 612
Fluowet® FS 612 is a perfluoro alkylethyl triethoxy silane raw material for the preparation of easy-to-clean coatings. This clear colourless to pale yellow liquid is used for the synthesis of nanocomposites together with other silanes and partially hydrolysis of the silanes to produce reactive condensates. The perfluoroalkyl chain of Fluowet® FS 612 contributes to the hydrophobic and oleophobic effect of the coating. Water pearls of the coated surface and stains like lime soap can not adhere strongly to the surface. Suitable applications for easy-to-clean coatings are: ceramic tiles in kitchens; glass doors of shower cabins; ceramic sanitary ware, wash basins and bath tubes; metals and metal oxide surfaces; wood and paper; paint and coatings; and plastics and polymers.
Genagen® C 100
Genagen® C 100 is a nonionic emulsifier for the chemical industry. This colourless liquid is composed of coconut fatty acid polyethylene glycol ester with 10 moles ethylene oxide. Genagen® C 100 is resistant to water hardness salts and can be used in combination with other nonionic, anionic and cationic surfactants.
Genagen® CG 200
Genagen® CG 200 is an additive for the polyester industry. This slightly yellow liquid is composed of cocos fatty acid polyglycol ester. Genagen® CG 200 is resistant to water hardness salts and can be used in combination with other nonionic, anionic and cationic surfactants.
Genagen® COA
Genagen® COA is a new non-VOC coalescing agent for the effective reduction of minimal film formation temperature (MFFT) without impacting viscosity. Label-free and for all kinds of paints binders used in diverse decorative coatings applications.
Genamin® 10 R 200 D
Genamin® 10 R 200 D is a raw material for the chemical-technological industry. This slightly yellow paste is composed of didecyl amine, distilled. It is a starting material for quaternary ammonium compounds.
Genamin® 10 R 301 D
Genamin® 10 R 301 D is a raw material for the chemical-technological industry. This yellowish liquid is composed of didecyl methyl amine, distilled. It is a starting material for quaternary ammonium compounds.
Genamin® 12 R 302 D
Genamin® 12 R 302 D is a raw material for the manufacture of quaternary ammonium compounds, betaines and amine oxides. Dimethyl fatty alkylamines are liquid or pasty,water insoluble bases. They are readily soluble in organic solvents such as mineral oil, isopropanol and chloroform. The basicity of the dimethyl fatty amines is slightly less marked than that of primary and secondary fatty amines.
Genamin® 14 R 302 D
Genamin® 14 R 302 D is a raw material for the manufacture of quaternary ammonium compounds, betaines and amine oxides. Dimethyl fatty alkylamines are liquid or pasty,water insoluble bases. They are readily soluble in organic solvents such as mineral oil, isopropanol and chloroform. The basicity of the dimethyl fatty amines is slightly less marked than that of primary and secondary fatty amines.
Genamin® 16 R 302 D
Genamin® 16 R 302 D is a raw material for the manufacture of quaternary ammonium compounds, betaines and amine oxides. Dimethyl fatty alkylamines are liquid or pasty,water insoluble bases. They are readily soluble in organic solvents such as mineral oil, isopropanol and chloroform. The basicity of the dimethyl fatty amines is slightly less marked than that of primary and secondary fatty amines.
Genamin® 18 R 302 D
Genamin® 18 R 302 D is a raw material for the manufacture of quaternary ammonium compounds, betaines and amine oxides. Dimethyl fatty alkylamines are liquid or pasty,water insoluble bases. They are readily soluble in organic solvents such as mineral oil, isopropanol and chloroform. The basicity of the dimethyl fatty amines is slightly less marked than that of primary and secondary fatty amines.
Genamin® 20/22 R 302 D
Genamin® 20/22 R 302 D is a raw material for the manufacture of quaternary ammonium compounds, betaines and amine oxides. Dimethyl fatty alkylamines are liquid or pasty,water insoluble bases. They are readily soluble in organic solvents such as mineral oil, isopropanol and chloroform. The basicity of the dimethyl fatty amines is slightly less marked than that of primary and secondary fatty amines.
Genamin® 3119
Genamin® 3119 is a cationic surfactant for the chemical-technological industry. It is also used as a dispersing agent. This light brown liquid is composed of N-Tallow alkyl N,N-Bis-(3-aminopropyl)-amine.
Genamin® 8 R 200 D
Genamin® 8 R 200 D is a starting material for quaternary ammonium compounds. This colourless to slightly yellow liquid/paste is composed of dioctyl amine, distilled.
Genamin® 8 R 300 D
Genamin® 8 R 300 D is a raw material for the chemical-technological industry. This colourless to slightly yellow liquid is composed of tri-n-octyl amine, destilled. This product is insoluble in water and soluble in organic solvents or in diluted aqueous acids (accompanied by salt formation).
Genamin® 8/10 R 302 D
Genamin® 8/10 R 302 D is a raw material for the manufacture of quaternary ammonium compounds, betaines and amine oxides. Dimethyl fatty alkylamines are liquid or pasty, waterinsoluble bases. They are readily soluble in organic solvents such as mineral oil, isopropanol and chloroform. The basicity of the dimethyl fatty amines is slightly less marked than that of primary and secondary fatty amines.
Genamin® C 050
Genamin® C 050 is a surfactant for the chemical-technological industry. This yellowish to brownish clear liquid is a coconut fatty amine ethoxylate with 5 mol EO. The grade is composed of saturated C8-C18 fatty amines, predominantly C12-C14.
Genamin® C 100
Genamin® C 100 is a surfactant for the chemical-technological industry. This yellowish to brownish clear liquid is a coconut fatty amine ethoxylate with 10 mol EO. The grade is composed of saturated C8-C18 fatty amines, predominantly C12-C14. Genamin grades can be combined with all types at nonionic and cationic surfactants. The compatibility with anionic products must be checked for each case. The Genamin grades are resistant to most chemicals at typical concentrations used. They are insensitive to water hardness. Their specific surface active properties make them valuable bases and additives for the chemical technical industry. They can be used to manufacture textile auxiliaries (e.g. products for dyeing) mineral oil additives, crop protection products and pesticides, raw materials for cosmetics and adhesives.
Genamin® C 150
Genamin® C 150 is a surfactant for the chemical-technological industry. This yellowish to brownish clear liquid is a coconut fatty amine ethoxylate with 15 mol EO. This grade is composed of saturated C8-C18 fatty amines, predominantly C12-C14. Genamin grades can be combined with all types at nonionic and cationic surfactants. The compatibility with anionic products must be checked for each case. The Genamin grades are resistant to most chemicals at typical concentrations used. They are insensitive to water hardness. Their specific surface active properties make them valuable bases and additives for the chemical technical industry. They can be used to manufacture textile auxiliaries (e.g. products for dyeing) mineral oil additives, crop protection products and pesticides, raw materials for cosmetics and adhesives.
Genamin® C 200
Genamin® C 200 is a surfactant for the chemical-technological industry. This yellowish to brownish clear liquid is a coconut fatty amine ethoxylate with 20 mol EO. This grade is made of saturated C8-C18 fatty amines, predominantly C12-C14.
Genamin® CC 100
Genamin® CC 100 is a raw material for the manufacture of fatty amine ethoxylates and fatty amine salts. This grade is composed of primary fatty alkylamines. Primary fatty alkylamines are liquid or pasty, water insoluble bases. They are readily soluble in organic solvents such as mineral oil, isopropanol and chloroform.
Genamin® CC 100 D
Genamin® CC 100 D is a raw material for the chemical-technological industry. This grade is composed of a liquid coconut fatty amine, dist. Primary fatty alkylamines are liquid or pasty, water insoluble bases. They are readily soluble in organic solvents such as mineral oil, isopropanol and chloroform. This product is used as a raw material for the manufacture of fatty amine ethoxilates and fatty amine salts.
Genamin® CC 302 D
Genamin® CC 302 D is a raw material for the manufacture of quaternary ammonium compounds, betaines and amine oxides. Dimethyl fatty alkylamines are valuable raw materials for the manufacture of surfactants. These water insoluble tertiary amines can be readily converted to water-soluble salts, quaternary ammonium compounds, often referred to simply as "quats", are the most important.
Genamin® CC 500 A
Genamin® CC 500 A is a raw material for the chemical-technological industry. This product is composed of coconut fatty amine acetate. It is used as a floatation aid and anti-caking aid for certain minerals. It is also applied as an antistatic agent, hydrophobing agent for pigments, corrosion inhibitor, and emulsifier. Furthermore, this product is used in the textile and leather industries.
Genamin® CC 500 E
Genamin® CC 500 E is a cationic emulsifier for the chemical-technological industry. This light brown paste is composed of coconut fatty amine oleate. It is used as a demolding agent for the building industry. After storage of some months the color of the product may become darker.
Genamin® CHP 100 D
Genamin® CHP 100 D is a raw material for the chemical-technological industry. This colourless, clear liquid is composed of N-cyclohexyl-1,3- propane diamine, dist.
Genamin® CS 200
Genamin® CS 200 is a raw material for the chemical-technological industry. It is used as a starting material for quaternary ammonium compounds. This white up to light yellow paste/wax is composed of dicoco alkyl amine.
Genamin® CS 302 D
Genamin® CS 302 D is a raw material for the manufacture of quaternary ammonium compounds, betaines and amine oxides. Dimethyl fatty alkylamines are valuable raw materials for the manufacture of surfactants. These water insoluble tertiary amines can be readily converted to water-soluble salts, quaternary ammonium compounds, often referred to simply as "quats", are the most important.
Genamin® LA 302 D
Genamin® LA 302 D is a raw material for the manufacture of quaternary ammonium compounds, betaines and amine oxides. Dimethyl fatty alkylamines are valuable raw materials for the manufacture of surfactants. These water insoluble tertiary amines can be readily converted to water-soluble salts, quaternary ammonium compounds, often referred to simply as "quats", are the most important.
Genamin® LAP 100 D
Genamin® LAP 100 D is a raw material for the chemical-technological industry. This pasty to waxy substance is composed of lauryl propylene diamine, dist. It can be applied in detergents, pigment dispersions, and in the textile and leather industry. It is also used as an emulsifier, corrosion inhibitor, flotation agent, and chemical intermediate.
Genamin® MY 302 D
Genamin® MY 302 D is a raw material for the manufacture of quaternary ammonium compounds, betaines and amine oxides. It is composed of dimethyl myristyl amine, dist. Dimethyl fatty alkylamines are liquid or pasty, water insoluble bases. They are readily soluble in organic solvents such as mineral oil, isopropanol and chloroform. The basicity of the dimethyl fatty amines is slightly less marked than that of primary and secondary fatty amines.
Genamin® O 020 Special
Genamin® O 020 Special is a surfactant for the chemical industry. The Oleylamine (O) grade is predominantly unsaturated C18 fatty amines.
Genamin® O 080
Genamin® O 080 is a surfactant for the chemical-technological industry. This yellowish to brownish clear liquid is composed of oleylamine with 8 mol EO. The "O" group (Oleylamine) is distinguished as predominantly unsaturated C18 fatty amines. Genamin grades can be combined with all types at nonionic and cationic surfactants. The compatibility with anionic products must be checked for each case. The Genamin grades are resistant to most chemicals at typical concentrations used. They are insensitive to water hardness. Their specific surface active properties make them valuable bases and additives for the chemical technical industry. They can be used to manufacture textile auxiliaries (e.g. products for dyeing) mineral oil additives, crop protection products and pesticides, raw materials for cosmetics and adhesives.
Genamin® O 200
Genamin® O 200 is a surfactant for the chemical-technological industry. This product is a yellowish to brownish clear liquid. The Oleylamine (O) grade is predominantly unsaturated C18 fatty amines. Genamin grades can be combined with all types at nonionic and cationic surfactants. The compatibility with anionic products must be checked for each case.
Genamin® OL 100
Genamin® OL 100 is a raw material for the manufacture of fatty amine ethoxilates and fatty amine salts. It is used as an antistatic agent, flotation agent, anti-caking agent, corrosion inhibitor, and as an emulsifier for resin. Furthermore, this product is applied in pigments and in the textile and leather industry. Primary fatty alkylamines are liquid or pasty, water insoluble bases. They are readily soluble in organic solvents such as mineral oil, isopropanol and chloroform. This liquid, pasty grade is composed of soybean amine, dist.
Genamin® OL 100 D
Genamin® OL 100 D is a raw material for the manufacture of fatty amine ethoxilates and fatty amine salts. It is used as an antistatic agent, flotation agent, anti-caking agent, corrosion inhibitor, and as an emulsifier for resin. Furthermore, this product is applied in pigments and in the textile and leather industry. Primary fatty alkylamines are liquid or pasty, water insoluble bases. They are readily soluble in organic solvents such as mineral oil, isopropanol and chloroform. This liquid, pasty grade is composed of soybean amine, dist.
Genamin® OLP 100
Genamin® OLP 100 is a raw material for the chemical-technological industry. It is used in detergents, pigment dispersions, as an emulsifier, corrosion inhibitor and as a chemical intermediate. This liquid grade is composed of soybean propylenediamine. It is also used in processing, dispersing aids and crop applications.
Genamin® S 020 Special
Genamin® S 020 Special is a surfactant for the chemical-technological industry. This yellow to brown liquid is composed of stearylamine with 2 mol EO. The "S" grade means the group is distinguished by its saturated C16-C18 fatty amines.
Genamin® S 080
Genamin® S 080 is a surfactant for the chemical-technological industry. This yellow to brown liquid is composed of stearylamine with 8 mol EO. The "S" grade means the group is distinguished by its saturated C16-C18 fatty amines.
Genamin® S 100
Genamin® S 100 is a surfactant for the chemical-technological industry. This yellow to brown liquid is composed of stearylamine with 10 mol EO. The "S" grade means the group is distinguished by its saturated C16-C18 fatty amines.
Genamin® S 120
Genamin® S 120 is a surfactant for the chemical-technological industry. This yellow to brown liquid is composed of stearylamine with 12 mol EO. The "S" grade means the group is distinguished by its saturated C16-C18 fatty amines.
Genamin® S 150
Genamin® S 150 is a surfactant for the chemical-technological industry. This yellow to brown liquid is composed of stearylamine with 15 mol EO. The "S" grade means the group is distinguished by its saturated C16-C18 fatty amines.
Genamin® S 200
Genamin® S 200 is a surfactant for the chemical-technological industry. This yellow to brown liquid is composed of stearylamine with 20 mol EO. The "S" grade means the group is distinguished by its saturated C16-C18 fatty amines.
Genamin® S 250
Genamin® S 250 is a surfactant for the chemical-technological industry. This nearly white, pasty to waxy substance is composed of stearylamine with 25 mol EO. The "S" grade means the group is distinguished by its saturated C16-C18 fatty amines.
Genamin® SH 100
Genamin® SH 100 is a raw material for the chemical-techonological industry. This wax-like grade is composed of stearylamine. Primary fatty alkylamines are liquid or pasty, water insoluble bases. They are readily soluble in organic solvents such as mineral oil, isopropanol and chloroform. This product is used as a raw material for the manufacture of fatty amine ethoxilates and fatty amine salts.
Genamin® SH 100 D
Genamin® SH 100 D is a raw material for the chemical-techonological industry. This wax-like grade is composed of stearylamine, dist. Primary fatty alkylamines are liquid or pasty, water insoluble bases. They are readily soluble in organic solvents such as mineral oil, isopropanol and chloroform. This product is used as a raw material for the manufacture of fatty amine ethoxilates and fatty amine salts.
Genamin® SH 200 FLA
Genamin® SH 200 FLA is a raw material for the chemical-technological industry. These white to light yellow flakes are composed of bis-hydrogenated tallow amine, technical. Genamin® SH 200 FLA is a starting material for dialkyl methyl amines and quaternary ammonium compounds.
Genamin® SH 200 V
Genamin® SH 200 V is a raw material for the chemical-technological industry. This white to light yellow paste/wax is composed of C14-18-Dialkyl amine (vegetable origin). Genamin® SH 200 V is a starting material for dialkyl methyl amines and quaternary ammonium compounds.
Genamin® SH 200 V FLA
Genamin® SH 200 V FLA is a raw material for the chemical-technological industry. These white to light yellow flakes are composed of C14-18-Dialkyl amine (vegetable origin). Genamin® SH 200 V FLA is a starting material for dialkyl methyl amines and quaternary ammonium compounds.
Genamin® SH 302 D
Genamin® SH 302 D is a raw material for the manufacture of quaternary ammonium compounds, betaines and amine oxides. This grade is composed of dimethyl stearyl amine, dist. Dimethyl fatty alkylamines are valuable raw materials for the manufacture of surfactants.
Genamin® T 020 Special
Genamin® T 020 Special is a surfactant for the chemical-technological industry. This yellowish to light brownish paste is composed of tallow fatty amine ethoxylate with 2 mol EO. The "T" (Tallow fatty amine) group is distinguished as saturated and unsaturated C16-C18 fatty amines.
Genamin® TA 100
Genamin® TA 100 is a raw material for the chemical-techonological industry. This pasty, wax-like grade is composed of tallow fatty amine. Primary fatty alkylamines are liquid or pasty, water insoluble bases. They are readily soluble in organic solvents such as mineral oil, isopropanol and chloroform. This product is used as a raw material for the manufacture of fatty amine ethoxilates and fatty amine salts. It is also applied as an antistatic agent, flotation agent, anti-caking agent, emuslifier for resin, and corrosion inhibitor. Furthermore, it is used in the textile and leather industry.
Genamin® TA 100 D
Genamin® TA 100 D is a raw material for the chemical-techonological industry. This pasty, wax-like grade is composed of tallow fatty amine, dist. Primary fatty alkylamines are liquid or pasty, water insoluble bases. They are readily soluble in organic solvents such as mineral oil, isopropanol and chloroform. This product is used as a raw material for the manufacture of fatty amine ethoxilates and fatty amine salts.
Genamin® TA 200
Genamin® TA 200 is a raw material for the chemical-technological industry. It is used as a starting material for quaternary ammonium compounds. This white to light yellow paste is composed of di-tallow fatty amine.
Genamin® TA 302 D
Genamin® TA 302 D is a raw material for the manufacture of quaternary ammonium compounds, betaines and amine oxides. This grade is composed of dimethyl tallow fatty amine, dist. Dimethyl fatty alkylamines are valuable raw materials for the manufacture of surfactants.
Genamin® TAP 100
Genamin® TAP 100 is a raw material for the chemical-technological industry. This yellowish up to brownish soft paste is composed of tallow fatty propylene diamine. It is used in detergents, pigment dispersions, and the textile and and leather industry. This product is also applied as an emulsifier, corrosion inhibitor, emulsifier for bitumen, anti-stripping agent, flotation agent and chemical intermediate.
Genamin® TAP 100 D
Genamin® TAP 100 D is a raw material for the chemical-technological industry. This white to yellowish soft paste is composed of tallow fatty alkyl propylenediamine, dist. It is used in detergents, pigment dispersions, and the textile and and leather industry. This product is also applied as an emulsifier, corrosion inhibitor and chemical intermediate.
Genapol® 1879
Genapol® 1879 is a nonionic emulsifier for emulsion polymerization. It is composed of alkyl polyethylene glycol ether in water. Genapol® 1879 is a nonionic emulsifier for the chemical industry and is used as an emulsifier in oil/water systems and for emulsion polymerization. Genapol® 1879 is suitable for use in the production of polymer dispersions based on vinyl acetate and comonomers, acrylic esters and comonomers and butadiene/styrene latices. This product stabilizes the polymer dispersion during and after polymerization and prevents coagulation.
Genapol® 3214
Genapol® 3214 is a nonionic emulsifier for emulsion polymerization. This colourless liquid is composed of alkyl polyethylene glycol ether in water. Genapol® 3214 is a nonionic emulsifier for the chemical industry and is used as an emulsifier in oil/water systems and for emulsion polymerization.
Genapol® ED 3060
Genapol® ED 3060 is a low-foaming wetting and dispersing agent for aqueous paints and coatings. This yellowish liquid improves the compatibility of pigments and minerals with polymers and binders in aqueous coatings and improves the color strength of organic pigments like phthalocyanine blue or red and yellow azo pigments.
Genapol® O 250
Genapol® O 250 is a nonionic emulsifier for the chemical industry. This white wax is composed of cetyl/oleyl polyethylene glycol ether with 25 moles ethylene oxide. Genapol® O 250 is used in emulsion polymerization of the following monomers: vinyl acetate together with acrylates, vinyl chloride or ethylene; and acrylate and acrylate / styrene dispersions.
Genapol® O 300
Genapol® O 300 is a nonionic emulsifier for the chemical industry. This white wax is composed of oleic alcohol polyethylene glycol ether with 30 moles ethylene oxide. Genapol® O-300 is used in emulsion polymerization of the following monomers: vinyl acetate together with acrylates, vinyl chloride or ethylene; and acrylate and acrylate / styrene dispersions.
Genapol® PF 10
Genapol® PF 10 is a low foaming, nonionic surfactant for the chemical industry. This clear, colorless liquid is composed of a block copolymer of propylene oxide and ethylene oxide, containing 10% w/w ethylene oxide. Genapol® PF 10 has good wetting and dispersing action coupled with low foaming tendency. Within the Genapol® PF series, the products with a lower degree of ethoxylation have a better foam-suppressing effect than the products with a higher degree of ethoxylation.
Genapol® PF 20
Genapol® PF 20 is a low foaming, nonionic surfactant and defoamer for use in detergents and cleaning agents. It is also used as a low foaming emulsifier in emulsion polymerization and as a dispersing agent for pigment pastes and preparations. This product is a slightly cloudy, colorless liquid that is composed of block copolymer of propylene oxide and ethylene oxide, containing 20% w/w ethylene oxide.
Genapol® PF 40
Genapol® PF 40 is a low-foaming nonionic surfactant for the chemical industry. It can be used in combination with other nonionic, anionic and cationic surfactants. Genapol® PF 40 is resistant to water hardness salts and to acids and alkalis in the concentrations normally used. This cloudy, colourless solution has good wetting and dispersing action coupled with low foaming tendency.
Genapol® PF 80 Powder
Genapol® PF 80 Powder is a low-foaming, nonionic surfactant for the chemical industry. This white powder can be used in combination with other nonionic, anionic and cationic surfactants. Genapol® PF 80 powder is resistant to water hardness salts and to acids and alkalis in the concentrations normally used. This product has good wetting and dispersing action coupled with low foaming tendency.
Genapol® PL 120
Genapol® PL 120 is a low foaming, nonionic surfactant for the chemical industry. This cloudy liquid is composed of fatty alcohol EO/PO-Adduct. It is used as a low foaming wetting agent for paints and coatings. This product is unaffected by water hardness constituents, and it is considerably resistant to aqueous acids and alkalis. As a nonionic surfactant, it can be used in combination with other nonionic compounds and with anionic and cationic substances.
Genapol® T 800 Powder
Genapol® T 800 Powder is a nonionic surfactant for the chemical-technological industry. This white powder is composed of fatty alcohol polyglycol ether with 80 mol EO based on saturated C16-C18 alcohol. As a nonionic surface active substance Genapol® T 800 powder can be combined with other nonionic, anionic and cationic products. It is used as a wetting agent for powder coatings and concrete. This product is also used as an emulsifier and dispersing agent for pigment pastes, paints and binders.
Genapol® X 020
Genapol® X 020 is a nonionic surfactant for the chemical industry. This colourless, turbid liquid is composed of isotridecyl polyethylene glycol ether with 2 moles ethylene oxide. It is compatible with anionic, cationic and other nonionic surfactants and resistant against strong alkaline and acid solutions. Genapol® X 020 is used as a wetting agent and emulsifier e.g. in detergents, industrial & institutional cleaners or in wax and silicon emulsions.
Genapol® X 050
Genapol® X 050 is a nonionic emulsifier for the chemical industry. This colourless, clear liquid is compatible with anionic, cationic and other nonionic surfactants and resistant against strong alkaline and acid solutions. Genapol® X 050 is used as a wetting agent and emulsifier e.g. in detergents, industrial & institutional cleaners or in wax and silicon emulsions.
Genapol® X 089
Genapol® X 089 is a nonionic emulsifier for the chemical industry. It is composed of isotridecyl polyethylene glycol ether with 8 moles ethylene oxide. Genapol® X 089 is used as a wetting agent, emulsifier and dispersing agent e.g. in detergents, industrial & institutional cleaners, in emulsion polymerization or in wax and silicon emulsions. This product is compatible with anionic, cationic and other nonionic surfactants and is resistant against strong alkaline and acid solutions.
Genapol® X 090
Genapol® X 090 is a nonionic emulsifier for the chemical industry. This colorless, turbid liquid is compatible with anionic, cationic and other nonionic surfactants and is resistant against strong alkaline and acid solutions. Genapol® X 090 is used as a wetting agent, emulsifier and dispersing agent e.g. in detergents, industrial & institutional cleaners, in emulsion polymerization or in wax and silicon emulsions.
Genapol® X 100
Genapol® X 100 is a nonionic surfactant for the chemical industry. This white waxy product is used e.g. in detergents, industrial & institutional cleaning formulations, in emulsion polymerization and as an emulsifier for polyolefin waxes or silicon oils.
Genapol® X 1000
Genapol® X 1000 is a nonionic emulsifier for the chemical industry. This white wax is composed of isotridecyl polyethylene glycol ether with 100 mole ethylene oxide. Genapol® X 1000 can be used as an emulsifier for bitumen emulsions and emulsion polymerization.
Genapol® X 1003
Genapol® X 1003 is a nonionic emulsifier for the chemical industry. It is composed of isotridecyl polyethylene glycol ether with 100 mole ethylene oxide. Genapol® X 1003 can be used in emulsion polymerization to reduce coagulation and to improve electrolyte resistance and freeze/thaw stability. Genapol® X 1003 is added to the emulsion either before, during or after the polymerization process. This product can be used as an emulsifier for bitumen emulsions.
Genapol® X 1005
Genapol® X 1005 is a nonionic emulsifier for the chemical industry. It can be used in emulsion polymerization to reduce coagulation and to improve electrolyte resistance and freeze/thaw stability. Genapol® X 1005 is added to the emulsion either before, during or after the polymerization process. This product can also be used as an emulsifier for bitumen emulsions.
Genapol® X 108
Genapol® X 108 is a nonionic emulsifier for the chemical industry. It is composed of isotridecyl polyethylene glycol ether with 10 mole ethylene oxide. This product is used in detergents, industrial & institutional cleaners, in emulsion polymerization or in wax and silicon emulsions.
Genapol® X 158
Genapol® X 158 is a nonionic emulsifier for emulsion polymerization. It is composed of isotridecyl polyethylene glycol ether with 15 mole ethylene oxide. Genapol® X 158 is used in emulsion polymerization of vinyl acetate, acrylate and styrene / acrylate dispersions to reduce coagulation and to improve electrolyte resistance and freeze/thaw stability. This product is used either during or after polymerization.
Genapol® X 208
Genapol® X 208 is a nonionic emulsifier for emulsion polymerization. It is composed of isotridecyl polyethylene glycol ether with 20 mole ethylene oxide. Genapol® X 208 is used in emulsion polymerization of vinyl acetate, acrylate and styrene / acrylate dispersions to reduce coagulation and to improve electrolyte resistance and freeze/thaw stability. Genapol® X 208 is used either during or after polymerization.
Genapol® X 307
Genapol® X 307 is a nonionic emulsifier for emulsion polymerization. It is composed of isotridecyl polyethylene glycol ether with 30 mole ethylene oxide. The use of Genapol® X 307 in emulsion polymerization of vinyl acetate, acrylate and acrylate / styrene dispersions reduces coagulation and improves electrolyte resistance and freeze/thaw stability. This product is added to the emulsion either before, during or after the polymerization process.
Genapol® X 407
Genapol® X 407 is a nonionic emulsifier for emulsion polymerization. The use of Genapol® X 407 in emulsion polymerization of vinyl acetate, acrylate and acrylate / styrene dispersions reduces coagulation, improves electrolyte resistance and freeze/thaw stability. This product is added to the emulsion either before, during or after the polymerization process.